+38 (057) 759-14-59
+38 (050) 368-86-94
+7   (499) 677-21-51

Request a call back

You can leave a phone number in the form below. We will contact you.

Pipe installation

Ways of spiralnovityh pipes SPIRO

Sewer pipes SPIRO recommended for use in places not exposed to direct sunlight.

For spiralnovitye SPIRO pipes, the following connection methods:

1. Flare connections

Flare connections

Sewer pipes SPIRO spiralnovitye with a nominal inner diameter of not more than 800 mm can be connected to each other into the socket with rubber gaskets that provide a tight seal.

Rubber grommets are supplied with the pipe, standard pipe length is 6 or 12m (other lengths on request).

The geometric dimensions of pipes SPIRO with a nominal inner diameter of 200-800 mm, SN4

d D L
мм мм мм
200 250 200
250 300 200
300 350 210
350 400 210
400 450 230
450 500 230
500 586 250
600 686 250
700 800 270
800 900 280
 

2. Extrusion welding

Extrusion welding

Welding SPIRO polyethylene sewer pipes made from the outside by means of an extruder.

For large diameter pipe welding is done on both sides.

This compound has a very high resistance to fracture, and are homogeneous. It is recommended to connect the pipes SPIRO large diameters, as well as the reconstruction of pipeline rehabilitation method.

 

3. Threaded connection

Threaded connection pipe SPIRO

It is used mainly in the reconstruction of the destroyed pipelines and installation of crossings under roads.

Due to the spiral structure sewer pipe SPIRO, it is possible to make internal and external threads.

 
Thread length, mm 150 150 150 150 150 150 180 180 200 200
dвн, mm 200 350 400 450 500 600 700 800 900 1000
 

4. Screw connection with seal

Screw connection with seal

The use of rubber seals when connecting sewer pipes SPIRO can simplify and reduce the cost of installation of pipelines in the real world.

A rubber seal provides a watertight connection. The speed of execution of tasks on laying of utilities allows to stack large volumes over the same period of time.

 

5. Shrink tape

connection with shrink tape

Heat-shrinkable tape can be used for the outer seal, and also in combination with other materials. When used for special purposes shrink tape bought separately.

 

6. Segment bends SPIRO

segment bends

Plastic connecting pieces of pipe segments made by butt welding. These parts allow to optimize the flow pipe when laying pipelines and reduce construction time.

Material PE, PP, hardness: L, C, ST, T (more reinforced on request), r=1,5xdвн

 
dвн a=30 a=45 a=60 a=90
z z z z
мм мм мм мм мм
300 340 420 480 670
350 350 450 520 740
400 370 480 550 810
450 410 540 620 910
500 450 590 680 1000
600 540 710 820 1200
700 630 840 960 1400
800 690 920 1060 1575
900 700 960 1120 1690
1000 720 1000 1180 1810
1050 740 1050 1230 1900
1200 760 1110 1320 2080
1400 790 1190 1440 2330
1500 1000 1440 1700 2650
1600 1020 1480 1760 2770
1800 1040 1560 1880 3020
2000 1070 1650 2000 3270
2200 1300 1930 2320 3710
2400 * * * *
2500 * * * *
2600 1350 1930 2500 4200
2800 * * * *
3000 * * * *
 

7. Segmental tees SPIRO

Segmental tees SPIRO
 
dвн z
мм мм
200 450
300 520
350 545
400 575
450 600
500 780
600 835
700 895
800 950
900 1000
1000 1065
1200 1180
1500 1340
1600 1400
1800 1520
2000 1650
2200 1725
2400 *
2500 *
2600 1925
2800 *
3000 *